I can't seem to install the safety lever so that it sits flush with the groove and so I cannot assemble the slide to the frame. What am I doing wrong.

 

Did you remove the pin?

 

Not on purpose, but yes and then had to partially disassemble the FCU. Actually I installed an intellifire trigger and in the process it fell out. I did uncover he blind hole and thought after many tries I had it. But, no.

 

May be easier to remove the takedown lever bar, trigger bar and disconnector so you can line the hole up with the lever to get the pin in far enought to hold it in place. Sig Guy has some great videos to help.

 

I did that but will check sig guy videos.

Thank you.

 

i have not done this modification... but...

I believe you need a grip module that specifically accommodates the added safety lever:

P365 9MM/380 MANUAL SAFETY GRIP MODULE - BLACK

GRIP MODULE ASSY, 365, 9, MANUAL SAFETY, BLK

www.sigsauer.com

 

No, look at the photos. Not a grip safety. It is in all p365 variants.

 

This is caused by the pre-travel adjustment on the Trigger.

 

I can't seem to install the safety lever so that it sits flush with the groove and so I cannot assemble the slide to the frame. What am I doing wrong. View attachment 679779 View attachment 679780

This is caused by the pre-travel adjustment on the Trigger.

Would you please elaborate?

 

Can you push it forward and down with your finger? Sometimes I have to do that to reinstall the slide on mine. If not, have you disassembled the FCU at all? If so, did you remove the pin that holds the safety lever? It looks like your FCU is not seated fully in the grip module, which leads me to believe the pin may not be installed fully and is sticking out the left side and interfering with the FCU going in all the way.

 

Can you push it forward and down with your finger? Sometimes I have to do that to reinstall the slide on mine. If not, have you disassembled the FCU at all? If so, did you remove the pin that holds the safety lever? It looks like your FCU is not seated fully in the grip module, which leads me to believe the pin may not be installed fully and is sticking out the left side and interfering with the FCU going in all the way.

Thank you, I have pushed that lever down but it will not go down enough to clear the slide end plate.

I did replace the trigger so yes I did disassemble the FCU which is when that lever fell out. After geting it back in twice I had the same issue. The FCU does seem to want to can't towards the right when viewed from the back.

I do think the pin is inserted all the way but will check again.

 

Would you please elaborate?

Here is a great article that explains how the take up on the trigger affects the position of the striker safety lever.

 

How did you make out?

 

I did replace the trigger so yes I did disassemble the FCU which is when that lever fell out.

These are the kind of details that are important to provide so folks are able offer assistance.

 

Haven't done it yet. Need to watch the SigGuy video and waiting for a response from Tyrant CNC.

 

The SigGuy video he has two back to back will help ya perfectly! Its on your other thread.

 

This is a duplicate of the following thread:

https://www.sigtalk.com/posts/6653246/

 

So did I fall for another scam?

 

Its actually pretty easy, you just need to tip the FCU down on its side, visually line up the safety dog in the hole, then slide the pin in from the backside. It helps if you have a pin the same size to line it up. Then you can push the safery pin in and push the other pin out the other side.
I've changed dozens of triggers and it has happened to me a number of times.

 

Would you please elaborate?

Here is a great article that explains how the take up on the trigger affects the position of the striker safety lever.

Hi Andy,

I don't see the article or link.

 

Hi Andy,

I don't see the article or link.

The admin moved it.
Here it is again.

 

Okay I followed the SigGuy video and still nt staying out of the way. So now I am waiting for Tyrant CNC customer service.

 

My guess is it has something to do with the “30% reduced pre-travel” of the Tyrant trigger.

 

Yes, for sure. The more pre-travel you take out of the trigger, the more that little bar goes up.