SIG Talk banner
  • Notice image

    SigTalk is a forum community dedicated to SIG Sauer enthusiasts. Come join the discussion about Sig Sauer pistols and rifles, optics, hunting, gunsmithing, styles, reviews, accessories, classifieds, and more!

RITON OPTICS 3 TACTIX MPRD 2: Mounted on P322

2196 Views 9 Replies 9 Participants Last post by  rtl
I ordered it this past Tuesday the 24th. Mounted it today on my P322. Holy Sheep ****..!!
I got this today the 28th. Mounted it, zeroed it, WOW.

I am attaching the link to this in this message. $99.99. Free shipping. I zeroed this using a sandbag rest at 10yds using CCI Stingers. The shots were POA and POI after a few adjustments.

Again; It was dead on zero with Stingers. I also shot CCI Mini-Mags at the same distance. Just a little off from POA. Not much. I am still taking it to the indoor range this weekend and fine-tuning the zero. 馃槑

Mounting it was easy. The stock screws worked. One drop of blue Loc-Tite just to make sure. The screws that came with this would not mount. The threads were too big.

$99.99 is a GREAT bargain for this. Considering the same sights out there going for $149-$299.



Riton Optics 3 Tactix MPRD 2 3.0 MOA Red Dot Sight Bulk Packaging - 3TMPRD2

Everyone again; Have a safe holiday weekend..!!
AK...
  • Like
Reactions: 2
1 - 10 of 10 Posts
Wow.. great deal
I鈥檝e got RomeoZero Elite,
love the red reticle..
I agree that it鈥檚 a great deal and works great on the P322. 25 yards:
White Black Font Line Rectangle
See less See more
  • Like
Reactions: 3
I ordered it this past Tuesday the 24th. Mounted it today on my P322. Holy Sheep ****..!!
I got this today the 28th. Mounted it, zeroed it, WOW.

I am attaching the link to this in this message. $99.99. Free shipping. I zeroed this using a sandbag rest at 10yds using CCI Stingers. The shots were POA and POI after a few adjustments.

Again; It was dead on zero with Stingers. I also shot CCI Mini-Mags at the same distance. Just a little off from POA. Not much. I am still taking it to the indoor range this weekend and fine-tuning the zero. 馃槑

Mounting it was easy. The stock screws worked. One drop of blue Loc-Tite just to make sure. The screws that came with this would not mount. The threads were too big.

$99.99 is a GREAT bargain for this. Considering the same sights out there going for $149-$299.



Riton Optics 3 Tactix MPRD 2 3.0 MOA Red Dot Sight Bulk Packaging - 3TMPRD2

Everyone again; Have a safe holiday weekend..!!
AK...
Where did you get the screws to mount the riton red dot?
The following information came from someone else's post somewhere I can not find again. Due credit to that gentleman.
The best screw size is M3x.5x12. I got mine a Lowe's. The screws have a phillips head, which works fine, since you only tighten to 8-10 inch pounds.The factory and these screws are smaller in diameter than the holes in the Riton sight. Slipping a short piece of shrink tube over the screw and shrinking it gives a much tighter fit in the mounting holes of the sight. I just got my P322 and only have about 400 rounds through it but the sight has stayed tight. Hope this helps.
I picked up some shouldered screws from McMaster. I鈥檇 tried a few countersunk style ones but couldn鈥檛 keep them holding.
I picked up some shouldered screws from McMaster. I鈥檇 tried a few countersunk style ones but couldn鈥檛 keep them holding.
Could you post the part numbers you got from mcmaster? I am unsure on the exact length I should get.
Got these to mount the Holosun 407K X2, and worked like a charm!


A bit pricy, but they include a shoulder along with the countersunk head.
Thanks. Unfortunately, even the screws from mcmaster will be that expensive with shipping.
  • Like
Reactions: 1
Thanks. Unfortunately, even the screws from mcmaster will be that expensive with shipping.
In Tucson the local ACE Hardware carry M3 .5 x 10 &12. About $.50 each
RTL
1 - 10 of 10 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top