SIG Talk banner
Cancel
  • Notice image

    SigTalk is a forum community dedicated to SIG Sauer enthusiasts. Come join the discussion about Sig Sauer pistols and rifles, optics, hunting, gunsmithing, styles, reviews, accessories, classifieds, and more!

P320 FCU

873 Views 12 Replies 12 Participants Last post by  cmdrcody, 
I
Just bought a p320 today and I went to take out my FCU and it’s stuck in there or really hard to get out. Looked at YouTube videos to see how to take it out and everyone’s looked super easy to take out. Any hell?
Reply
Save
Like
  • Like
Reactions: 1
1 - 13 of 13 Posts
GunCrazedRedneck
Remove take down lever, the push forward and up on back of trigger is how I do it.
Reply
Save
Like
  • Like
Reactions: 5
T
Talk to the fcu while you wiggle the fcu out.

you gotta finesse her a little bit and she’ll come right out.
Reply
Save
Like
  • Like
Reactions: 3
T
get the tool made by the Sig Armorer. It is well worth the money. Saves headaches for sure. P320 Accessibility Tool | The Sig Armorer
Reply
Save
Like
  • Like
Reactions: 5
SMISSCCJ
After the slide and takedown lever have been removed, grab the rails (from the rear) and pull up and back
Reply
Save
Like
  • Like
Reactions: 1
VA GS
I had one that was very tight in certain frames when new. Leather work gloves and pull up on the rails to protect your fingers from any sharp edges.

Better tight than loose.
Reply
Save
Like
  • Like
Reactions: 2
S
tactical.dev

Takedown Tool for SIG P320

This is the Takedown Tool for the Sig P320 - the design came from my need to takedown my cerakoted P320 and then others saw this tool and wanted one and even added features like the keychain hole (Thanks Alex!) and the tolerance for Gen1 takedown levers (Thanks Ben!) as well as a take down lever...
tactical.dev tactical.dev
Reply
Save
Like
  • Like
Reactions: 2
M
Yeah, it is stiff when it is new...
Reply
Save
Like
  • Like
Reactions: 2
Ecrevisse
GunCrazedRedneck said:
Remove take down lever, the push forward and up on back of trigger is how I do it.
Click to expand...
This works as does the Sid Armor’s tool.
Reply
Save
Like
  • Like
Reactions: 1
ProofMark
Ecrevisse said:
This works as does the Sid Armor’s tool.
Click to expand...
My Custom Works FCU is very tight in all grip modules. I bought a Sig Aromorers Toll just for that FCU. My “regular” FCU’s seem a bit less tight.
Reply
Save
Like
C
My easy way to remove without a tool.

1. Remove slide and takedown lever.

2. Put the slide on the two front tabs of FCU.

3. Lift the slide to rotate the FCU and it should come right out.


Sent from my iPhone using Tapatalk
Reply
Save
Like
FreeTacos
I just slide a small punch or a plastic pry tool under the rail and pry it up.
Reply
Save
Like
C
Ecrevisse said:
This works as does the Sid Armor’s tool.
Click to expand...
Who is Sid Armor and why is his tools so admired?

Reply
Save
Like
  • Haha
Reactions: 2
1 - 13 of 13 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
SIG Talk
A forum community dedicated to SIG Sauer Pistols and SIG Sauer Rifles owners and enthusiasts. Come join the discussion about optics, hunting, gunsmithing, styles, reviews, accessories, classifieds, and more!
Full Forum Listing
Explore Our Forums
SIG Sauer Pistols 🙋‍♂️ Member Introductions Guns P250, P320, P320 X-5, M17, & M18 Pistols P365
Top