Search Results for ‘virtus’

So i have a nice line worn into the upper receiver from the striker retaining pin, And i have seen posts from others who have as bad of a wear line as mine where it is a bright silver line. Has this been solved or is it just an issue that needs to be lived with? Note: this is only an upper kit...

This is purely due to my OCD lol. I just got my first suppressor yesterday and wont be able to take it out until tomorrow. I got everything installed and for some reason it looks like the suppressor is pointing up a bit. Is that normal or could that cause issues like a baffle strike? I did put a...

I was looking over my mcx virtus upper and noticed that the receiver feed ramps dont come close to lining up with the barrel feed ramps. Is that normal? All my other guns have flush feed ramps. I attached pictures of my mcx virtus feed ramps. Is that gap normal?

I got a sig mcx 9" 300 blackout Virtus and went ahead and picked up a dead air sandman s. I have a bunch of dead air flash hiders on different rifles so I figured it would be a first good can. My question is with the sandman s being a low back pressure can how reliable is the sig mcx shooting...

I know the sandman s has lower backpressure. For people running the sandman s on a sig mcx 9" 300 blk Virtus, how is the reliability with subs and supers?

Hello, can anyone help me identify what two (different) triggers sets these are? Thanks!! (left hammer looks different than the right hammer)

I have a sig mcx Virtus 300 blackout and I am trying to install my dead air break. Having a hard time hitting the recommended torque spec with the 90 degree shoulder adapter. My reaction rods don't fit the Virtus so how should I change the muzzle device? Just take the barrel out and throw it in...

I'm trying to install a new dead air muzzle device on my mcx virtus with the sig 90 degree shoulder adapter and its damn near impossible to get the correct torque value cause the shoulder has some give to it. Without rocksett applied I have to turn the muzzle device almost 200 degrees to hit 30...

I'm trying to install a new dead air muzzle device on my mcx virtus with the sig 90 degree shoulder adapter and its damn near impossible to get the correct torque value cause the shoulder has some give to it. Without rocksett applied I have to turn the muzzle device almost 200 degrees to hit 30...

Hey guys, was wondering if someone could help me. I have a Virtus 11.5” and was hoping to pick up the Rattler blackout barrel (and probably a new rail too) to be able to convert to a Rattler. Has anyone tried this? The website makes it seem like you can only use a Rattler barrel on a legacy MCX...

Hello, hope you’re doing well! I need some help please. I have an MCX Virtus and am getting a 6.75” blackout barrel and short MI hand guard for it. Unfortunately, I have to wait a bit for a suppressor. What would you recommend for a compatible high quality muzzle device in the meantime? (Flash...

Its been a hell of a year sourcing parts for my build. I got a sig virtus upper and found a complete mcx legacy rifle. I sold the legacy upper and I am now using the virtus upper on teh legacy lower. I didnt even think to see if the legacy lowers were compatible with virtus uppers. Question is...

Hi guys, Just thought I’d share my experience building my own Go Bag for my Virtus SBR and hope it helps some out there. After investing several hundreds of hours searching and researching (as I always do with most things I buy) for an edc bag solution that looked more civilian than mil, I...

I just picked up one of those Stop Box AR Chamber locks when they were on sale to see if it would fit my MCX Hybrid build with a Virtus upper. The it is a little tight, but it clicks into place without too much fuss and with no modification. Apparently the main issue with these locks was...

Hey Everyone! I just got my first Sig! MCX Virtus Patrol 16in 300BLK and been debating on the best optic set up. ACOG or LPVO?! Thoughts? I plan on running it with a 35degree off set red dot as well! Since it’s a 300blk I’m really stuck on if I should invest in the ACOG 300blk edition since I...