suppressor

I’m considering purchasing a Surefire SOCOM300-SPS Fast-Attach Suppressor for use on a Sig MCX Rattler .300 Blackout SBR. Is there enough space to mount a SOCOM300-SPS Fast-Attach Suppressor and its quick attach flash hider suppressor adapter to the MCX Rattler without hinderance from the...

Would anyone here know for certain whether or not the SRD45 suppressor would be rated/ able to handle 350 Legend? From what I've read (but not seen on the shelves yet), I understand that there will be both sub- and supersonic loads being made. Is it right that the suppressor might indeed handle...

Would anyone here know for certain whether or not the 45 SRD suppressor would be rated/ able to handle 350 Legend? Apologies if this is not the right area to put this; I didn't see an area relating to suppressor questions. Tight lines. Straight shots, Wink

I have a SS suppressor (awaiting paperwork/stamp) for a full-size .45 that I plan to use for home/ self defense. As a nightstand gun, is a suppressor an advantage as far as saving hearing in an indoor environment- or a liability as far as over-readiness/ overeager indication, etc.? Would it be a...

MCX Rattler 5.5", as well as Virtus Patrol 16", barrel thread neck seems to be so close inside the hand guard narrow opening. Can a Sandman-S with a KeyMo QD mount fit on a Sandman muzzle break attached on the Rattler short barrel?

So I'm looking for a good AR 300-BLK in a "pistol" form-factor and I'm considering the Rattler PSB, which I would then convert to SBR via online ATF Form-1... takes a few weeks instead of many months for approval. My intention / end-state is a suppressed SBR in a foldable and very compact...

Anybody out there use this combination? The piston "bottoms out" at the end of the threads. I tighten it and then adjust with the rotation lever. It "looks" and "feels" OK, but this can doesn't bottom out at the end of the barrel threads on my P226 or P229 (same threads as a MPX). I'm...

Literally "just" received my stamp late last week ... submitted paperwork on March 6 for the Silencerco Chimer-300 that I just received approval for. That means the wait time was one week shy of 9 months. This is the last of three I ordered. Each took between 8 and 9 months and was approved...

Hello, I need your expertise... I have a First Generation Sig Sauer MCX with 11.5 inch barrel fitted with a Advanced Armament M4-2000 suppressor. Went to the range yesterday and fired 100 rounds of American Eagle 5.56, 55 grain FMJ. Out of 100 rounds 29 rounds were light primer strikes. When I...

Hey guys, Looking for some input on something; I currently have orders in place for the SRD45, and the SRD9 suppressors...I already bought a Sig 1911 TB Tacops for the SRD45 and am looking at something for the SRD9. I was looking at possibly getting the P320-RX because I like the built in...

I'm looking to get an SBR and put a can on it. My local shop advised me on the set-up with MPX SBR with a Rugged Obsidian 45 on it. He suggested the can b/c it can be used with so many calibers (45, 9mm, I've even heard it can go on rimfires) which would be a nice option. I wanted to see if...

I gave my gunsmith my 300BLK barrel and the 5/8x24 muzzle brake for the 338Ti-QD and he couldn't install it: "With body of muzzle brake tightened against taper-loc, muzzle of barrel protrudes too far through, preventing brake portion from being timed with use of the crush washer." Has anyone...

P226 .22lr threaded barrel adapter? Ok so I have a liberty mystic x can and a 13.5x1 lh booster for my p226 9mm... I just got the .22lr conversion w/ threaded barrel for the p226. Apparently the .22lr barrel has a 9x.75 thread and the adapter it comes with is a 9x.75 female to a 1/2x28...

Hey guys, I would greatly appreciate your guidance. I have an MPX SBR awaiting ATF approval and wanted to stay with Sig for my suppressors. I was waiting for the release of the 9mm SRD9 for about 10 months and I finally gave up. I ordered the SRD45 just prior to the 41F change this summer...

Hello Just got off the phone Sig and they confirmed I have two routes form my MCX SBR (both are back ordered). I already have mil-spec SBR (form processing) lower I'll be using. The MCX lower will remain non-AFT regulated. AR Conversion Kit. This includes a full w/hand guard 9in 300blk...

Need your thoughts please! Half way there with my MCX and MPX platforms, but need your experience on suppressors. For the sophomore in the crowd, it is very difficult to read between the marketing lines. I have set a personal target to purchase before 41F, to avoid providing BATFE additional...

Any experience with Precision Armament AFAB or EFAB? Have Sig 716 and want to add a Hybrid. Looking for input on all manufacturers and personal experiences and/or thoughts. Seems to be a lot of manufacturers. Application is deer, coyotes, and hogs. Most shots less than 300 yes..

Greetings fellow gun nuts :) Just bought an MPX 8" 9mm and looking to set it up. Hoping anyone with experience can steer me in the right direction. First order of business is a silencer. I've been doing a lot of research but wish I could talk to people who have used cans on this gun...

I have threaded barrel M11-A1 9mm I have a suppressor that I used on my H&K MP5K that was a bayonet/twist on connection. Three lug. I know that there are 28mm adapters to get me to 3 lug. How ever, I'm wondering if any one has experience do in this and if my suppressor has to be custom to this...

I'm the proud owner of a Sig P226s X5 tactical. It's my favorite pistol. This is the last P226 X5 that was made with a threaded barrel from Germany, and is not the "new" model X5 that Sig sells in the US today. I can doubletap an eight inch target at 50 yards with this pistol, and with a red...