-M1x1.5 Viton Fluoroelastomer O-Ring, 75A Shore Durometer, Round, Black, 1.5 millimeters ID, 3.5 millimeters OD, 1 millimeters Width (Pack of 25)

Name: -M1x1.5 Viton Fluoroelastomer O-Ring, 75A Shore Durometer, Round, Black, 1.5 millimeters ID, 3.5 millimeters OD, 1 millimeters Width (Pack of 25)
Price: 12.99 USD

MoRivera · Jan 21, 2016

curlysir said:
If you don't want to pay the $3-4 for the o-ring these appear to be the same but at a cost of 54 cents each. http://www.amazon.com/gp/product/B005RUPDMI?psc=1&redirect=true&ref_=oh_aui_search_detailpage

I just received 1 of 3 take down levers I ordered and the o-ring went on and installed without any problem. I did put a drop of oil on the new o-ring.

It's funny that you bring that up because I actually broke the new O-ring as I was trying to stretch it out. I put some oil on, but maybe I either didn't wait long enough or more likely stretched it badly. Luckily, the older one came off and fit on the new TDL just fine. But yeah, I was going to head over to Home Depot or something to get more spares. So the ones you posted are the right size?

MoRivera · Feb 10, 2016

MoRivera said:
I just ordered these.....

Robot Check

Basically enough to last a lifetime even if I get more P320's.

Wl518 said:
010 Buna-N O-Ring, 70A Durometer, Black, 1/4" ID, 3/8" OD, 1/16" Width (Pack of 100): O Ring Seals: Amazon.com: Industrial & Scientific

Cheap O-rings

Caution: Neither of these worked for my P320 TDL. They don't quite fit snugly in the TDL's slot, and the TDL does not go into the frame all the way. Looks like I'll be ordering some from SIG.

d2randall · Feb 21, 2019

al120hp said:
I am going to put my AAC- Ti-rant 45 on my MPX this week. Will post a report asap

I have a AAC Ti-Rant 45S with Fixed Spacer threaded with a 13.5x1LH to .578x28RH MPX barrel thread adapter (USMACHINEGUN.COM) for my Gen II 4.5" and 8" barrels. The thread adapter is attached with high temperature Rocksett all-purpose ceramic adhesive cement.

Blowback is minimal and not an irritant. I use 9mm 147gr ammo which is subsonic by design. Since the Ti-Rant 45S is for .45ACP there is some sound reduction efficiency loss; however, it is not that apparent to the naked ear. I would expect IMHO, that you would loose about 3db with a Ti-Rant 45S versus a Ti-Rant 9 on a MPX.

I run the Ti-Rant wet and dry. Wet using a water-base clear wire lubricant. Tap water in the suppressor tends to add to blowback for the first 2-3 rounds (i.e. burnt powder and steam); however, the water-base lubricant does not add to blowback. Use of the "wet" can does lower the db, as well as, minimizing the first round muzzle/suppressor flash (i.e. caused by burning up the oxygen in a cold suppressor).

Another little trick is to put an O-ring on the barrel shoulder; as you screw on the suppressor, the O-ring snugs up against the barrel shoulder securing the suppressor from rotating after a couple of magazines of rounds.

The reason I use a .45ACP can vs a 9mm is due to having other .45ACP pistols and didn't desire to purchase a 9mm can just for the MPX. However, I'm researching 9mm cans.

d2randall · Jun 29, 2019

Concur, O-Ring.
I use these: Viton

Rated to 400 degrees F. Usually replace around 100 rds depending on rate of fire and just how hot the suppressor got. Even if the o-ring melts it is easily removed with a cleaning brush.

Some folks use plumbers tape, but I find that it melts quickly.

d2randall · Jul 12, 2020

Purchasing new barrels with right-hand thread is the permanent fix, but expensive.
I have a MPX Gen II with 8" and 4.5" 13.5x1LH barrels using a AAC Ti-Rant RH suppressor.
I purchased from USMACHINEGUN.COM left-hand to right-hand thread barrel adapters. The type of adapter you would most likely need is US Machinegun: *Sig Sauer MPX & PISTOLS 13.5x1 LH to 1/2x28 RH Thread Adapter, SIG SAUER MAGAZINES & PARTS, SIG-135TA - verify before purchase.

1. Thread the adapter with rocksett compound to the Sig barrel using 20ft-lb torque. Allow 24 hours for rocksett to dry.
2. Attach and hand-tighten RH suppressor to adapter mounted on barrel with a heat-resistant O-ring.
3. The O-ring will help resist the suppressor from naturally coming loose as firing rates and round counts increase.
4. Roughly every 1000rds, check the torque on the barrel thread adapter.

I have over 5000rds (i.e. 1000 with 8" barrel; 4000 with 4.5" barrel) through my MPX Gen II and have had no issues with barrel or suppressor stress/fatigue. Accuracy has been consistent with and without suppressor. When not using suppressor, I just hand-thread on the SIG MPX factory A2 flash hider.

curlysir · Jun 27, 2021

gp320 said:
The correct size o-ring for Sig P320 and variants is 1.6 x 6 mm Vitron or Burna-N works just fine. O-rings will be very tight when first installed and compress down with use.

I just replaced the O-ring on my P320 SC take down lever with this size (M1.6mm X 6.1mm) O-ring in Vitron and it worked fine. The original O-ring had split in half. Did lightly grease the O-ring with Lucas gun grease. The take down feels and works the same as my other P320s do when I remove the take down lever.

M1.6x6.1 Viton O-Ring, 75A Shore Durometer, Round, Black, 6.1 mm ID, 9.3 mm OD, 1.6 mm Width (Pack of 25): O Ring Seals: Amazon.com: Industrial & Scientific

www.amazon.com

d2randall · Dec 31, 2021

I have a MPX Gen 2 with a AAC Ti-Rant 45S suppressor with AAC fixed barrel spacer installed; yes, it is a .45 cal suppressor on a 9mm barrel. I have two barrels - 8" and 4.5" - both have a 13.5x1 LH to .578x28 MPX Barrel Thread Adapter, USMACHINEGUN.COM. I added to the suppressor an o-ring at the barrel interface that helps keep the suppressor from backing off the barrel under recoil.
With the 8" barrel, I average 1.5" groups at 25 yards and with the 4.5" barrel 2.1" groups at 25 yards. I use 147gr 9mm Hornady and Federal ammo.

Remove the suppressor and barrel assembly for cleaning, and the follow-up range check usually finds an average of 1" shift in POI - Re-zero and all is OK until next major cleaning. I am not seeing your problem, as described.

There was a great deal of work to get all these LH vs RH barrel/suppressor stuff to align correctly. I have a SIG SAUER MOD-X9 suppressor currently going through the ATF approval process that alleviates barrel interface issues. Expect ATF approval in April 2022 - I hope, maybe, I assume, fingers-crossed. . .

d2randall · 2022-11-26T08:13:25-0500

I use these O-rings: -M1.5x25.5 Viton Fluoroelastomer O-Ring, 75A Shore Durometer, Round, Black, 25.5 millimeters ID, 26.5 millimeters OD, 1.5 millimeters Width (Pack of 10): O Ring Seals: Amazon.com: Industrial & Scientific . Helps with keeping the suppressor from backing out during several action cycles.

-M1x1.5 Viton Fluoroelastomer O-Ring, 75A Shore Durometer, Round, Black, 1.5 millimeters ID, 3.5 millimeters OD, 1 millimeters Width (Pack of 25)

Forum Discussions about this Product

New Take down lever

MoRivera

New P320 TDL, Slide Catch, and Grip spotted in the wild

MoRivera

MPX suppressed

d2randall

Attachments

Threaded Barrel for P320

d2randall

MPX + Suppressor tightening issues

d2randall

Take down leaver Oring...

curlysir

M1.6x6.1 Viton O-Ring, 75A Shore Durometer, Round, Black, 6.1 mm ID, 9.3 mm OD, 1.6 mm Width (Pack of 25): O Ring Seals: Amazon.com: Industrial & Scientific

Suppressed MPX Accuracy Issues

d2randall

Suppressor not staying on MPX 4in

d2randall

Forum Reviews

Write a Review

Community Staff

Top Contributors this Month